Calibration&Replacement
How to adjust the laser beam path
How do I replace the Y-axis belt
Y-axis belt replacement and adjustment(Take the right side of the Y axis belt as an example) Tools needed M3 Screwdriver Plier 5.5mm wrench New belt A pair of scissors Masking tape Disassemble Turn off the machine and unplug the power cord. Remove ...
How to replace the controller board
Firstly, turn off the whole machine power. Export&Import the Vendor settings Before install the new one, please export the Vendor settings from the old controller. And please import the vendor settings after installing the new controller board. ...
How do I replace the X-axis belt
X-axis belt replacement and adjustment Tools needed M3 Screwdriver Plier 5.5mm wrench New belt A pair of scissors Masking tape Disassemble Turn off the machine and unplug the power cord. Remove the upper front door with keys that came with the ...
How to remove the honey comb table
The honey comb table needs to be cleaned after using for a period of time, how to remove it for clean, this video is for reference.
How to install the handle
Tool needed Installation Place the handle on the outside of the hole and the screws on the inside of the hole. Fix the screws by hand firstly. Then, fix the screws with the tool( using the end that the diameter is 14mm).
Reverse compensation/Scan offset
Before you use the laser machine. Please remove the transparent bag from the front of honey comb plate. The transparent bag has a set of USB flash drive, and an engraving test sample. The USB flash drive stores software, manuals, libraries, etc… ...
How to calibrate the working table to level
1. Two sides of the working table are not of the same height Turn off the whole machine power, manually pull one of the belts of Z axis so as to adjust the up and down of the working table height of this side and calibrate the level in this way. ...
How to improve engraving quality in the scan mode of X-swing
The engraving quality working on x_swing is generally worse than x_unilateralism, it usually results in ghosting effect or image offset or bi-directional engraving offset, like below. Notice : We generally use plywood or acrylic to test. x_swing ...
How to check if the slot switch is faulty
If the L-shape shaft is bent after being hit, how to solve it? 1. Please loose the screw use M2 screwdriver, and make the L-shape switch to straight and install it back. 2. Then install it back. 3. Push the X/Y-axis by hand, observe whether the L ...
How do I replace the drive shaft module?
Firstly, disconnect the machine from its power source Disassembly procedure: Toole needed: M3/M4/M5 Allen Wrench Tips: Loosen in anticlockwise, tighten in clockwise. 1. Loosen two upper screws on the buckle then take out the belt; 2. Unscrew and ...
Why noisy while moving laser head front and back, how to adjust?
When you move laser head front and back, two couplings make a lot of noise. Both sides of transmission shaft are not aligned. How to fix it? 1.Turn off the whole machine power. 2.Take out the belt by taking down the motor. 1). Loosen three screws ...
How to replace the rollers and adjust the X axis shaft?
Replace the rollers: Adjustment of X-axis shaft 1.Please check before adjustment ①Hold and shake it to check if it becomes loose.(can’t be wobble obviously) ②In the back of X Axis Shaft have four rollers, both of them should locate on the rail.(can ...
How to adjust the verticality between the X and Y Axis?
X Axis Turn off the whole machine power. There are four screws for each side, loosen them then you can fine tuning the angle of the X Axis. Shown as bellow. Diagonal line 1 = Diagonal line 2. Error value must be less than 0.5mm like below: ①If ...
How to adjust and replace the motor?
X-axis Motor 1. Firstly, disconnect the machine from its power source. Screw A: There are four screws A, for fixing the X motor; Screw B: It’s for adjusting the belt tension, please loosen the four screws A before adjust belt. 2. Click the link ...
How to replace the coupling
This video is for reference.
How to replace the Nova series DC tubes
Firstly, turn off the whole machine power. Video: Instructions (may vary but the principle is the same): Remove old part: 1. Unplug the wire between laser tube and laser power supply and take out from the hole, like below. 2.unfix the tube. ① ...
How to replace red dot pointer and cables
Replace red dot pointer （Unplug the old red dot pointer, reconnect the new one according to the original position.） 1. The red dot pointer is installed on the beam combiner, please loosen the screw fixing the red dot pointer, and then pull out the ...
Popular Articles
Material Test for All CO2 Glass Tubes
Test with 3mm plywood, LightBurn software, Engraving(Fill) and Cutting(Line) modes , 60W, 80W, 100W, 130W tubes. Engraving(Fill) 60W 80W 100W 130W Cutting(Line) 60W 80W 100W 130W Material test file download The lbrn files are attached
Equipment Info
Please follow our requirements strictly！ Please provide below information after thunder tech team confirming warranty! 1.Manufacturer's Label Location Of the OEM Machine Label The manufacturer's labels can be found as shown below: Example Machine ...
Warranty Requirements-Laser tube
Please follow our requirements strictly！ Problem description Please describe your problem to us and provide a video or photo. That's can help us to judge the issue easily. Video or photo must show the problem clearly. If you don't know how to ...
SAFETY INFO: Class 4 C02 Laser Radiation, PPE, & Fire Suppression
Overview This document covers some basic safety information on the processes of laser engraving. DISCLAIMER: Laser Engravers emit deadly high voltage and laser radiation capable of causing instant blindness and tissue damage. Lasers are a fire ...
Fire Risk - Never leave your machine unattended
We hear it all the time, don't run the laser unless you are monitoring it. This is from a client (VIDEO BELOW): PSA: I am guilty of reading about not leaving the laser unattended, but doing it anyway. An employee was cutting some acrylic and we are ...