How do I replace the X-axis belt

How do I replace the X-axis belt

X-axis belt replacement and adjustment

Tools needed

  • M3 Screwdriver
  • Plier
  • 5.5mm wrench
  • New belt
  • A pair of scissors
  • Masking tape


Disassemble

  1. Turn off the machine and unplug the power cord.
  2. Remove the upper front door with keys that came with the machine.


Note: Falling object! This object is not hinged and may fall if released unexpectedly.

  1. Move the laser head to the middle of the work area.
  2. Slightly loosen the Nuts with 5.5mm wrench that fix the belt, between side of the X-axis bracket and belt buckle.



  1. Loosen the four screws(Screw A) slightly.(Approximately 5mm outward so that it can be adjusted later).



  1. Loosen the four screws(Screw B) slightly which fix the belt.




  1. After loosening the Nuts and Screws, the belt should be slacked. 

      Note: please do not pull out the belt directly now!


Installment

  1. Paste the end of new and old belt with a piece of masking tape. Please make sure that the belt is not knotted during the process. 

Note: The side of the belt with the gear print must fit the gear.      



  1. Pull the belt out from the other side, then tear off the tape and remove the old belt.
  2. Fix the Screws B on the left（right is also OK） side to lock the belt.



  1. Pull the other end of belt with a plier (or pull it with your hand) to make sure the belt straight and as tight as possible.
  2. Fix the other two Screws B on the right side that you loosed.
  3. Make sure the belt runs in the center of the rail and does not rub any of the lips on the rail,if it is correct, lock the Screws A and Nuts back to their original positions.

      Note: The distance between the belt buckle and X-axis bracket should be 6-7mm.

      How to replace the X-Axis belt,please refer to this link below:

      How to replace the X Axis belt - YouTube



  1. Check the tension of the belt, if it’s too loose or tight, please adjust the tension of the belt according to below video link.

      How to adjust the tightness of the Y Axis belt - YouTube

      (There is no constant value for the belt tightness. If you just replace the X-axis belt, you can refer to the Y-axis belt tightness. )

      Test method: Gently press the belt with your hand, and the belt has a little elasticity.

  1. Move the laser head by hand to check if the laser head moves smoothly. 
  2. After you install it, if belt is too long, you can cut a piece off.
  3. Reinstall the upper front door and locked it.

End

    • Related Articles

    • How do I replace the Y-axis belt

      Y-axis belt replacement and adjustment(Take the right side of the Y axis belt as an example) Tools needed M3 Screwdriver Plier 5.5mm wrench New belt A pair of scissors Masking tape Disassemble Turn off the machine and unplug the power cord. Remove ...

    • X-axis not moving at all

      Reasons: 1. X-axis limit switch problem X-axis limit switch is located on the left side of x-axis,  like below. We have installed three limit switches before, and Omron is the one we are using now. Mechanical limit switch:   Slot limit switch: Omron ...

    • How to replace the rollers and adjust the X axis shaft?

      Replace the rollers:   Adjustment of X-axis shaft 1.Please check before adjustment ①Hold and shake it to check if it becomes loose.(can’t be wobble obviously) ②In the back of X Axis Shaft have four rollers, both of them should locate on the rail.(can ...

    • Y-axis not moving at all

      Reasons: 1. Rotary switch is turned on For 5-pin machine, the rotary-axis and y-axis can be switched, if the rotary switch is turned on, y-axis will not moving at all, and the rotary-axis will need to connect the rotary device. Solution: "I" means ...

    • How to adjust the verticality between the X and Y Axis?

      X Axis Turn off the whole machine power. There are four screws for each side, loosen them then you can fine tuning the angle of the X Axis. Shown as bellow.     Diagonal line 1 = Diagonal line 2.  Error value must be less than 0.5mm like below:   ①If ...