rd works
RDWorks-Scan offset testing
You can download this file to test and adjust the Scan Offset settings.
Why USB connection is not working-RDWorks
Reasons: 1. USB cable is loose or faulty Solution: Unplug the USB cable and plug it back, try again. If re-plug the cable, problem still exists. 2. USB driver is not installed successfully Before you install the software, please install the USB ...
Why does the graphic size that imported to RDWorks different from its original size
Reason: If the file being imported is DXF format, the problem maybe the original file and RDWorks have different units. For example, the unit of the original DXF file is “inch”, but in RDWorks, the DXF unit is set as “mm”. When you import the DXF ...
How to import PDF files into RDWorks
1. RDWorks cannot read PDF and open it directly. 2. Use CorelDraw to open/import PDF file firstly. Then save the graphic as DXF file. Like below: 3. Then RDWorks can read the DXF file, Just import the DXF file into RDWorks directly. 4. The ...
Wrong proportions from RDWorks
Reason: "Enable rotate engrave" is enabled. I’d like to cut a Rectangle at 30x30mm, however, it become 30×60.2 in simulation and in laser, Solution: Please make sure “Enable rotate engrave” is not ticked. End
Laser cutter has a wrong cutting/engraving size
Reason: Wrong pulse setting of X/Y axis motors Solution: 1. Please draw a 100x100mm square using the cut mode and send to your laser cutter and cut the square. 2. Let’s say the actual size of the square measured is 98x95mm 3. In RDWorks, go ...
RDWorks plug-in installation instructions
RDWorks plug-in installation instructions
USB connection-RDWorks
1. Connect the laser machine and PC with the USB cable that came with the machine. 2. Install the software, please install the USB driver first before press "Install". 3. Open RDWorks and test the connection as following: 4. Then you can ...
How to run several laser machines with one PC via USB cable connection
If there are several USB interfaces with your PC, it’s able for one PC (laser software) to connect with several machines. pc to hub , one port of the hub goes to laser But For USB connection as below, 1. Pc to hub , one port of the hub goes to laser. ...
How to setup wireless network connection for Thunderlaser machine
Here's what you'll need: A computer with wireless capability A wireless router An Ethernet cable A Thunder laser system Step: 1. router setup Use the Ethernet cable to connect the wireless router to the Ethernet port on your laser system. Connect the ...
Popular Articles
Material Test for All CO2 Glass Tubes
Test with 3mm plywood, LightBurn software, Engraving(Fill) and Cutting(Line) modes , 60W, 80W, 100W, 130W tubes. Engraving(Fill) 60W 80W 100W 130W Cutting(Line) 60W 80W 100W 130W Material test file download The lbrn files are attached
Equipment Info
Please follow our requirements strictly！ Please provide below information after thunder tech team confirming warranty! 1.Manufacturer's Label Location Of the OEM Machine Label The manufacturer's labels can be found as shown below: Example Machine ...
Warranty Requirements-Laser tube
Please follow our requirements strictly！ Problem description Please describe your problem to us and provide a video or photo. That's can help us to judge the issue easily. Video or photo must show the problem clearly. If you don't know how to ...
SAFETY INFO: Class 4 C02 Laser Radiation, PPE, & Fire Suppression
Overview This document covers some basic safety information on the processes of laser engraving. DISCLAIMER: Laser Engravers emit deadly high voltage and laser radiation capable of causing instant blindness and tissue damage. Lasers are a fire ...
Fire Risk - Never leave your machine unattended
We hear it all the time, don't run the laser unless you are monitoring it. This is from a client (VIDEO BELOW): PSA: I am guilty of reading about not leaving the laser unattended, but doing it anyway. An employee was cutting some acrylic and we are ...