Alarm message of LCD panel--Machine protected(New type sensor)

Alarm message of LCD panel--Machine protected(New type sensor)

Problem description:

 LCD panel shows the following information:


Reasons:


1.The door with sensor not close

Our machine has sensors for door protection, we've installed 5 door sensors totally. 2 mounted at top flap, 1 mounted at the front door, 1 mounted at the left-up side door, 1 mounted at laser tube cover.


Solution:

Please close all of them before starts to work.


2. The door sensor is not working


Each door sensor is being detected by a door sensor checking board. This board is installed in the right side door for nova35, 51, 63 or left side door for nova24. 


About door sensor checking board interface description:


1: 24V DC Voltage Power Input             7: spare interface of Signal Input

2: Signal Input for door sensor of S5     8: Signal Input for door sensor of S3

3: Spare interface of Signal Input           9: Signal Input for door sensor of S2 

4: Signal Input for door sensor of S7    10: Signal Input for door sensor of S1 

5: spare interface of Signal Input          11: Signal Output,where signal to controller board

6: “Maintenance” button                  12:Spare interface of Signal Output 

Each interface has a LED light to indicate the status, the yellow light for interface of signal input will be on while door sensor with same label is closed,once all doors with sensors installed are closed,the red light for signal output will be on and then send the signal to controller board.


Please find the door sensor checking board,then check status of yellow light for interface of signal input,the light will be off if door sensor is not working.

Find the corresponding position of door sensor according to the wire label.

Order:  S1= left side of top flap, S2 = right side of the top flap , S3= the front door, S5 = laser tube cover, S7 = left-up side door.

If your machine was produced before September 2019, the door sensor checking board is not installed on your machine. Please check the machine according to this link.

Alarm message of LCD panel--Machine protected(Old type sensor)

(1) The connector of door sensor is loose


Solution:

Please check if the connector for corresponding position of door sensor is loose or not. Below picture is for reference.


(2) Poor contact between the actuator and the sensor or door sensor faulty

Solution:

Please adjust the position of the actuator or sensor to align them. If the position is fine and the yellow light is still off from the checking board, this door sensor should be bad. Please contact us:tech@thunderlaser.com




3. The wires of DrProc and GND on CN2 is loose from controller board


The wires of DrProc and GND on CN2 is loose from controller board.


Solution:

Please check and confirm they are tight. 


End.

    • Related Articles

    • Alarm message of LCD panel--Machine protected(Old type sensor)

      Question: LCD panel shows the following information: Reasons: 1. The doors with sensor are not closed Our machine has protection sensors for door (front cover and laser tube cover), like below. Solution: Please close all the doors before starting ...
    • Alarm message of LCD panel-Water error

      Problem description: LCD panel shows the following information: Reasons: 1. Water chiller(water pump)is not turned on The switch in the red circle in the picture is not turned on. Solution: Please turn on the water chiller before power on the ...
    • Alarm message of LCD panel-No enough extend space

      Problem description: LCD panel shows the following information: Reason: 1.This problem only appears on engraving mode, it's caused by the buffer distance is out of bound.  For example, if you want to engrave a picture of 200×200mm, you move the laser ...
    • Alarm message of LCD panel-Frame X/Y Slop over

      Problem description: LCD panel shows the following information: Reason: 1.The size of the graphic is larger than the working area of the machine Solution: If your laser cutter's working area is 600×400mm, but you want to cut a graphic which larger ...
    • No response to LCD panel keys

      Problem description: When you turn on the machine, the machine can reset normally, but the buttons on the LCD panel do not respond when you click it. Reason: 1.The LCD panel cord is not firmly connected to the controller port. Solution: Unplug the ...